Knowing Plumbing Basics is Important When Installing a Bathtub
Knowing Plumbing Basics is Important When Installing a Bathtub
Blog Article
Just how do you feel with regards to Installing A Bathtub?
Mounting a bathtub isn't exactly rocket science, but it does need strong plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bath tub with a brand-new one is also a reasonably challenging task. If the old tub is conveniently easily accessible, the project can relocate quickly; if you need to open a wall surface to remove the old tub and also position the new bath tub, the job is much harder. In either situation, the task is within a home handyman's skills, although you will certainly require a helper to move out the old tub and also set in the new one. Make certain you have actually certified on your own for the work and are comfortable attempting it. Rather than working with a professional to take over a halfway-completed job, it is better to take into consideration employing one prior to you start. Opportunities are you may need a professional plumber to make tube connections.
This article will assist you install a brand-new bathtub in your washroom if you have actually already bought a brand-new tub and do not require to change the setup of your previous water pipes.
Your tools as well as material list ought to consist of the following:
Getting ready for the Installment
Firstly, the supporting frame supplied with the bath needs to be fitted (if called for) according to the supplier's instructions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is important to ensure that if the faucet features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bath, it is additionally reasonable to fit a supporting plate under the taps system to prevent pressure on the tub.
Fit the versatile tap ports to the bottom of the two taps utilizing 2 nuts and olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet with the hole in the bath. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you make use of all of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom need to currently prepare to be suited its final position.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water. After doing so, switch on the faucets to drain pipes any type of water staying in the system. The process of getting rid of the existing faucets can be fairly bothersome because of the limited access that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the faucets. Have a fabric ready for the remaining water that will come from the pipelines. When the supply pipelines have been eliminated, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleansed of any old sealing substance.
Before carrying on to fit the new taps, contrast the pipe links on the old taps to the new taps. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new faucets to fit.
Setting up the Bathtub
Using both wood boards under its feet, put the bathtub in the needed setting. The wood boards are valuable in evenly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 small points.
The following goal is to guarantee that the bath tub is leveled all round. This can be accomplished by checking the level and also changing the feet on the bath tub until the level reviews level.
To mount faucets, fit all-time low of the furthest flexible faucet adapter to the suitable supply pipeline by making a compression join; then do the very same for the other faucet.
Turn on the water and also inspect all joints and new pipework for leakages as well as tighten them if necessary. Fill up the bathtub and likewise examine the overflow outlet as well as the typical outlet for leakages.
Lastly, repair the bath paneling as described in the maker's instruction manual. Tiling as well as securing around the bath tub should wait up until the tub has been used at least once as this will certainly settle it right into its last setting.
Fitting New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and also the other end supplies a connection to the current supply pipes.
If you need to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the mounting hole in the bath/basin guaranteeing that the washers remain in place in between the tap as well as the sink. Safeguard the tap in position with the supplier offered backnut. As soon as the tap is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal tap connectors. The previous type should be connected to the tap finishes first, tightening up just by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bathroom fulfills the tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the fitting can move enough to break a stiff seal, causing the water to penetrate the wall in between the bath and the tiling, leading to difficulties with moisture and also possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your fixtures and also fittings. They are offered in tubes and also cartridges, and can securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with spins of soaked paper or soft rope. Keep in mind to always fill the bathtub with water before securing, to allow for the movement experienced when the bathtub is in usage. The sealer can crack relatively very early if you do not take into account this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently offered on the market. It is advisable to fit the tiles making use of water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very curious about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I hope you liked the entire blog post. Enjoyed our blog posting? Please share it. Let other people check it out. Thanks a bunch for your time. Don't hesitate to stop by our blog back soon.
Book Services Report this page